|
The term high voltage usually means electrical energy at voltages high enough to inflict harm on living organisms. Equipment and conductors that carry high voltage warrant particular safety requirements and procedures. In certain industries, ''high voltage'' means voltage above a particular threshold ''(see below)''. High voltage is used in electrical power distribution, in cathode ray tubes, to generate X-rays and particle beams, to demonstrate arcing, for ignition, in photomultiplier tubes, and in high power amplifier vacuum tubes and other industrial and scientific applications. == Definition == The numerical definition of 'high voltage' depends on context. Two factors considered in classifying a voltage as "high voltage" are the possibility of causing a spark in air, and the danger of electric shock by contact or proximity. The definitions may refer to the voltage between two conductors of a system, or between any conductor and ground. In electric power transmission engineering, high voltage is usually considered any voltage over approximately 35,000 volts. This is a classification based on the design of apparatus and insulation. The International Electrotechnical Commission and its national counterparts (IET, IEEE, VDE, etc.) define ''high voltage'' as above 1000 V for alternating current, and at least 1500 V for direct current—and distinguish it from low voltage (50–1000 V AC or 120–1500 V DC) and extra-low voltage (<50 V AC or <120 V DC) circuits. This is in the context of building wiring and the safety of electrical apparatus. In the United States 2011 National Electrical Code (NEC) is the standard regulating most electrical installations. There are no definitions relating to ''high voltage''. The NEC® covers voltages 600 volts and less and that over 600 volts. The National Electrical Manufacturer's Association (NEMA) defines high voltage as over 100kV to 230kV. British Standard BS 7671:2008 defines ''high voltage'' as any voltage difference between conductors that is higher than 1000 V AC or 1500 V ripple-free DC, or any voltage difference between a conductor and Earth that is higher than 600 V AC or 900 V ripple-free DC. Electricians may only be licensed for particular voltage classes, in some jurisdictions.〔One such jurisdiction is Manitoba, where the ''Electrician's Licence Act, CCSM E50'' establishes classes of electrician's licences by voltage.〕 For example, an electrical license for a specialized sub-trade such as installation of HVAC systems, fire alarm systems, closed circuit television systems may be authorized to install systems energized up to only 30 volts between conductors, and may not be permitted to work on mains-voltage circuits. The general public may consider household mains circuits (100–250 V AC), which carry the highest voltages they normally encounter, to be ''high voltage''. Voltages over approximately 50 volts can usually cause dangerous amounts of current to flow through a human being who touches two points of a circuit—so safety standards, in general, are more restrictive around such circuits.. The definition of ''extra high voltage'' (EHV) again depends on context. In electric power transmission engineering, EHV equipment carries more than 345,000 volts between conductors. In electronics systems, a power supply that provides greater than 275,000 volts is called an ''EHV Power Supply'', and is often used in experiments in physics. The accelerating voltage for a television cathode ray tube may be described as ''extra-high voltage'' or ''extra-high tension'' (EHT), compared to other voltage supplies within the equipment. This type of supply ranges from >5 kV to about 50 kV. In automotive engineering, high voltage is defined as voltage in range 30–1000 Vac or 60–1500 Vdc.〔UNECE regulation No 100 (revision 2, 12th August 2013), paragraph 2.17 http://www.unece.org/fileadmin/DAM/trans/main/wp29/wp29regs/2013/R100r2e.pdf〕 In digital electronics, a high voltage usually refers to that representing a logic 1 in positive logic and a logic 0 in negative logic. It is not used to indicate a hazardous voltage and levels between ICs to TTL/CMOS standards and their modern derivatives are well below hazardous levels. The highest in mainstream use were 15V for original CMOS and 5V for TTL but modern devices use 3.3V, with 1.8V or lower used in many applications. 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「High voltage」の詳細全文を読む スポンサード リンク
|